Fresh indoor air with plants

Remove VOC’s and improve indoor air quality with these 15 plants! Full article describing which toxins  are removed by which plant and some tips about caring for each type of plant at Mother Nature Network

  1. Aloe Vera
  2. Spider plant (Chlorophytum comosum)
  3. Gerber daisy (Gerbera jamesonii)
  4. Snake plant (Sansevieria trifasciata ‘Laurentii’)
  5. Golden pothos (Scindapsus aures)
  6. Chrysanthemum (Chrysantheium morifolium)
  7. Red-edged dracaena (Dracaena marginata)
  8. Weeping fig (Ficus benjamina)
  9. Azalea (Rhododendron simsii)
  10. English ivy (Hedera helix)
  11. Warneck dracaena (Dracaena deremensis ‘Warneckii’)
  12. Chinese evergreen (Aglaonema Crispum ‘Deborah’)
  13. Bamboo palm (Chamaedorea sefritzii)
  14. Heart leaf philodendron (Philodendron oxycardium)
  15. Peace lily (Spathiphyllum)

PV Installed

It took Adam and I and the electricians 4 days to install our 18 panel 4.5 kW grid-tied solar photovoltaic system. At two full stories to the eave, a 2 foot overhang, a 12:12 pitch, and a slippery-when-wet roof, a lift was certainly in order. After deciding layout, installation began with snapping a chalk line for the first rail. Working with Adam on our house again was fun in a nostalgic sort of sense. Of course, this time we were both getting paid as Sandri employees–it isn’t every day that you get to hire yourself!

Using a lift to install rails for solar photovoltaic PV

Adam and Spartan installing the first rail.

The rails are attached to the roof using S5!’s new Protea clip. It is specifically designed to adapt to any metal roof with trapezoidal ribs. The fantastic thing is that they don’t need to be sunk into the trusses/rafters. They simply attach to the metal rib using four gasketed sheet metal screws. These clips were a huge boon to us because our house has cathedral ceilings across the entire roof; no access to the trusses. The manufacturer claims the clips can take 1000# uplift. When we walked and moved around on the rails, Adam and I both felt that they were more stable than rails mounted with standard Eco-feet with L brackets.

S5! Protea clip solar bracket metal roof ribbed rib

The S5! Protea clip has a butyl adhesive strip underneath the clip that seals it to the sides of the rib. No caulk required! We did encounter a serious problem though. We use Ironridge’s XRS rail which asks for a 3/8″ bolt with a 9/16″ head to connect to the clip. Unfortunately, the vertical slot in the clip is 5/16″. We found out the hard way that you can’t get a 5/16″ bolt with a 9/16″ head. We solved the problem by having a local fabricator mill out the slot to 3/8″. It only added less than $2/clip. I am not sure if S5! would have had a solution for us because they did not return our phone calls or emails in a timely fashion. Schletter makes a comparable clip as well and if we do this again we will be looking into it.

Solar panels produce DC electricity so you need an inverter/s to convert to AC. Although somewhat more expensive than a single inverter, we chose to use micro-inverters. This means that each panel has a dedicated inverter beneath it. This allows the system to overcome some of the problems associated with shading. In a typical single inverter system, if any panel is shaded, all of the other panels can only produce as much as the shaded one. Since we have a large silver maple tree right next to our house micro-inverters were essentially a necessity. At present time, there are only a few microinverters on the market: PowerOne, Renesola, and Enphase. We went with Enphase in large part since they have been on the market the longest. When you choose a micro-inverter you are also signing up for the same company’s monitoring system. You can log into your system via a web portal and see statistics for each panel as well as the entire system. If any panels are not functioning you will know.

Sparta installing solar PV electric photovoltaic on roof

Adam took this awesome shot from the lift. I love how it makes everything look 2 dimensional. It also reminds me of old video games like Mario Brothers; in this case the rails are the different levels that I could jump to. The units attached to the rails are the micro-inverters. The tilt for the solar hot water drain-back system is quite visible from this angle. Not all of the clips for the remaining rails have been installed. Photo Adam Heintz

Before we put on the panels I took a final set of solar access photographs using our Solmetric Suneye camera that uses a fish eye lens to photograph the sky. After orienting the camera towards south and leveling it you take a photograph that is instantly analyzed by the on-board software. Our annual solar access average is at least 85%. I say at least because we removed one final branch using the lift after the shots were taken.

Suneye Solmetric solar access compilation

Left to right is East to West on the roof.

I wanted to use US made solar panels so we went with American Choice panels sold by Renewable Sales. The panels are in fact re-branded 1Soltech panels made in Texas. Each panel is rated to create 250 watts/hour. The rating system baseline is actually somewhat worse than the amount of sun we get in Greenfield Massachusetts so, shading aside, one can expect to see more than 250 watts per panel under ideal conditions.


Our soon to be net-plus home.

As solar installers, Adam and I often get asked if we install systems with battery back ups. Unfortunately, battery technology/costs are not at a place where it is economical. However, there are a couple of promising workarounds coming on the market that, when the grid is down, allow electricity from the panels to be used in real time without batteries. One of them is an inverter by SMA that provides up to 1500 watts on a dedicated switched outlet.

Make the leap and go solar!

Make the leap and go solar! Photo Adam Heintz

How to grow fresh air

I recently watched this TED talk entitled How to Grow Fresh Air. It has significant implications for our existing buildings that have poor air quality and for our new buildings that are being built to super-tight standards. If the power goes out and we are relying on our HRV’s and our ERV’s to bring us our healthy air Kamal Meattle says that we can rely on these three house plants to sustain us:

  1. Areca Palm  (Chrysalidocarpus lutescens) – Turns CO2 into O2 during the daytime
  2. Mother-in-law’s tongue (Sansevieria trifasciata) – Turns CO2 into O2 during the night time

  3. Money plant  (Epipremnum aureum) Removes – VOC’s


Cost Breakdown of Construction

The total cost of construction from clearing land until we were able to move in was about $161,100.
The final cost of completion will probably be closer to $165,000 as there are many small things that still need to be done, (trim, painting the third floor room, kitchen counter top, closet doors etc.). Also, one must keep in mind that my labor was free as well as the help of many friends and family. We received $15,100 in rebates and tax incentives bringing the total cost down to $146,000. Our 1500 square foot (S.F.) house cost $97.30/SF to build.

Cost breakdown by type of expenditure

Materials $90,245.09
Labor $60,655.35
Permits, fees, engineering $4,490.70
New tools $4,336.65
Equipment and tool rental $2,973.18
Fuel $1,559.44
Food $434.70
Trash, disposal costs $384.61
Other $290.36

Cost breakdown by construction area

Doors, windows, interior window trim, and extension jambs $18,787.55
Framing $17,840.95
Insulation (labor & material, includes foundation insulation) $15,946.51
Foundation for home and garage $15,248.53
Siding, soffit, exterior trim $13,965.51
Sitework $12,460.50
Plumbing (labor and material) $10,218.69
Other $6,933.52
Electrical $6,868.67
Roof (Material and labor both sheathing and metal) $4,801.80
Porch $4,010.37
Drywall $3,255.16
HRV & Ductwork (material only, no labor cost) $2,793.22
Paint (labor and material) $2,738.45
Heat pump (material and labor) $2,600.00
Floors $1,901.39
Stairs $1,643.28
Driveway $1,475.00
Tiling bathroom and kitchen counter $1,353.52
Create lumber from trees from site $740.36
Solar hot water (after rebates and incentives) $269.45